How do I reset my Maytag Atlantis washing machine?

How do I reset my Maytag Atlantis washing machine?

The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.

Why is my washer washing but not draining?

Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.

Why is my washer spinning but not draining?

The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. It could be clogged, kinked, or even positioned incorrectly if you had to remove the drain tube to make another repair already.

Do Maytag washers have a reset button?

The Maytag washer doesn’t have a reset button. If you need the reset button, you have to use the ‘Power/Cancel’ button. Push it to stop the current cycle. Select a new cycle and then press ‘Start/Pause.

Where is the reset button on a Maytag washer?

Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.

Why is my Maytag washer not draining or spinning?

A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.

Why does water stay in washing machine drum?

Water In Bottom of Washing Machine Drum: Why It Happens Your lid mechanism is broken or not engaging fully. Your drain or hose is clogged. Your load was too large for a good spin cycle. Your washing machine’s sensors are damaged or old.

How do you manually drain a washing machine?

If not, follow these steps:

  1. Step 1: Turn off the power and lay down towels.
  2. Step 2: Locate the drain hose at the back of the washing machine.
  3. Step 3: Drain the water.
  4. Step 1: Turn off the power and lay down towels.
  5. Step 2: Locate the drain hose.
  6. Step 3: Drain the water.
  7. Step 4: Scrub the filter.

How do you troubleshoot a Maytag washer?

– Assess the load. – Determine whether the washer is plugged into the electrical outlet. – Remove any kinks from the drain hose. – Close the washer’s lid securely to add pressure to the lid switch. – Avoid overcrowding your load; an unbalanced, heavy load can contribute to excessive water fill that can leak.

How to clean your Maytag Atlantis washer?

Open the washer lid or door and remove any clothing or items.

  • Place an affresh ® Washer Cleaner tablet in the bottom of the washer basket.
  • Do not place an affresh ® Washer Cleaner tablet in the detergent dispenser.
  • Do not add any detergent or other chemical to the washer when following this procedure.
  • Close the washer lid or door.
  • What are the problems with Maytag washers?

    16 years’ experience in successful complaint resolution

  • Each complaint is handled individually by highly qualified experts
  • Honest and unbiased reviews
  • Last but not least,all our services are absolutely free
  • How to troubleshoot a Maytag washer on Spin Cycle?

    Turn the washer on a cycle.

  • Check if the tub is rotating around at all: When it doesn’t rotate at all,it’s likely the clutch is worn out.
  • If the clutch is worn out,you’ll need to replace it.